Skip to main content

KA8 Foam 2.4m AREA17 Build Blog


 Building the 5mm Balsa Tail, Fin and Rudder



Comments

Post a Comment

Popular posts from this blog

Foamboard Spitfire Build

AREA17 Foam-board Spitfire (Night Flyer Addition) Based on The FliteTest Spitfire   https://www.flitetest.com/articles/ft-spitfire-build Find us on Facebook    AREA17 CoG on Wing Spar line (65mm from leading edge) Tools Required * Sharp Blade               * Clear tape * Ball Point Pen            * Optional 10mm x 0.5mm carbon blade * Hot Glue Gun            * Icy pole sticks * Set Square Hardware Required to Finish * Motor Brushless 2826 to a 2836 around 1300/1500kv 8x6 prop (looking for 180-220 watts) * 1500-2200 mah 3s lipo min 40c Not suitable for 4s..... * 30-40 amp ESC * 3 Mini servos 1.6kg to about 2.6kg or 4 with an optional rudder eg HXT900/ EMAX ES08A * 4 Extension leads * TX and min 4 Ch RX * Velcro for battery * Control linkages and horns * Paper ribbon attached to fin for combat ** Optional carbon blade spar reinforcement (10mm x 0.5mm) Parts Supplied * Three  Laser-Cut Foam Board Sheets     (Depending on supply can be the brown or white Flite Test foam b
5 comments
Read more
  Combat Monkey Build Wingspan 750mm Laser cut 5mm Foam Board $15   The kit includes: Foamboard airframe components Ply and popsicle sticks for the motor mount. Corflute fuselage underside   What you need to complete: 3 x 9g Mini Servos  HXT900, MG90 etc Motor 2830 1200 kv to 2836 1500 kv 8x6 Prop (folding is better) 1300mah 3 cell lipo 30 amp ESC with BEC Sticky tape for hinges 3 control horns and 1.6mm piano wire 4ch RX Paper Party Streamers  about 40mm wide and at least 5m long   Tools: Hot Glue Gun and Sticks Box Cutter Scrape pieces of foam board to wipe off excess glue. Z bender Build With a sharp blade release all the foam board components from the backing sheet. Carefully deepen the hinge lines on the ailerons and elevator without cutting right through then bend back to form a hinge.  If you cut through, just tape the component back in place with clear sticky tape. Bevel the rearward side of the hinge surfaces forty-five degrees
Post a Comment
Read more
  The full size  SZD-30 Pirat  is a single-seat multipurpose  glider aircraft  from the  Polish  firm  PZL Bielsko  which first flew in 1966, and started production in 1967. This RC scale version of the SZD-30 Pirat is 3.2 metre wingspan or 21% scale. Wing area:  62sq/dm, 960 sq ins Weight: 2.6/3kg CoG: 76 to 80mm from leading edge Servos: 2x Aileron min 5kg, 1x Elevator min 2.2kg, 1x Rudder 4kg, 2x Airbrake 2.2 kg, Tow Release 4kg (based on deflection at 70kph)  This kit  includes: *Fuselage – CNC Foam cores ready for 2mm balsa planking. $50 *Wings –Built up, kit includes ribs, leading and trailing edges, main spars and shear webs. $60  or EPS foam version cores, jackets and end ribs $50 *Tailplane – EPS foam core ready to be laminated with 1.0mm balsa – $10  *Fin – EPS foam core ready to be laminated with 1.5mm balsa $10 *3d Printed canopy frame $10 *PVC Clear Canopy $10 *12mmx10mm Ali Joiner Bar $5 This kit does not contain electric/electronic components, balsa planking, wing skins,
Post a Comment
Read more